📞 929-235-1233 💬 WhatsApp 📧 Email

Home › Office News › 155 70th Street

155 East 70th Street — Oversize Steel Windows with Reeded Glass, and Four Shower Panels with a Notch: Project Log

Office News  ·  In progress  ·  Upper East Side townhouse: stair-hall steel windows and bathrooms on floors 2, 3 and 4  ·  Last updated 19 November 2026

Location155 East 70th Street, Lenox Hill, Upper East Side, Manhattan
ScopeCustom oversize steel windows with reeded glass in the stair hall, and four fixed frameless shower panels, one on floor 2, two on floor 3, one on floor 4
Steel windowsCustom-fabricated oversize steel windows, divided lites, glazed with reeded (fluted) glass; installed, stair framing in progress
Glass1/2-inch tempered, clear or low-iron to be circled on the sign-off sheet, flat polished edges
Detail3/4 × 3/4-inch notch in the bottom corner of every panel, bottom right viewed from outside the shower
StatusShop drawings P-1 to P-4 issued for field verification and sign-off, 17 Nov 2026; not yet released to production
Log3 entries, latest 19 Nov 2026

What This Page Is

This is an Office News case study: a job written up as it happens rather than after it is finished. Each step adds a dated entry below with what we measured, what we drew, what we flagged and what was decided. This one follows four fixed shower panels through the part of a shower job that decides whether the glass fits: field dimensions on a site sketch, a one-page shop drawing per panel, the field supervisor’s verification against the opening, and only then release to the tempering plant. The process is described in general in how we measure, verify and release shower glass for production; this page is that process on a live job.

The Job

A townhouse rebuild on East 70th Street between Lexington and Third, on the Upper East Side. We have two scopes in it: the oversize custom steel windows that light the stair hall, already installed and logged below, and the shower glass. The house has a bathroom on each of floors 2, 3 and 4, and two on floor 3. Each shower gets a single fixed glass panel, no door: a fixed shower panel standing on the curb, clamped to the wall, open at the other end. The panels are tall, all within an eighth of an inch of 84 inches, and they differ in width from 30 to nearly 66 inches, so each is drawn and verified on its own sheet. Every panel has the same small detail: a 3/4 × 3/4-inch notch cut out of the bottom corner on the wall side, which lets the glass sit past a lip at the base of the wall and still land flat on the curb. A notch that size is cut and polished before tempering; it cannot be added after, which is why the corner it goes in has to be right on the drawing.

Project Log

19 November 2026 — The stair-hall steel windows, installed and glazed with reeded glass

Looking up the stair well: the stacked steel windows, divided lites, reeded glass, with the stair still in rough framing.

Where the job is: the other half of our work in this house is in. The stair hall rises the full height of the building against the rear wall, and that wall is glazed with a stack of custom oversize steel windows, one above the other, each divided into lites by slim steel muntins. They are glazed with reeded glass: glass with fine parallel flutes rolled into one face, which lets the full daylight in and turns the view of the neighboring lot into a soft blur. On a townhouse stair, where the rear windows look straight at the building behind, that is the point: light without a view in either direction, and no blinds on a wall nobody can reach.

Why steel, why oversize: the openings are tall and the architect wanted the thinnest possible frame around a lot of glass, which is what steel does that aluminum and wood cannot at this size; the muntins carry the divided-lite pattern of the facade without turning into bars. Each window was fabricated to the opening, delivered through the house and set from the stair scaffold before the stair itself was framed, because once the treads are in there is no way to get a lite that size to the wall. The reeded glass is insulated, flutes to the inside so the exterior face is flat and cleans like any window; where a lite is within reach of the stair it is tempered.

What is left on the windows: final glazing bead check and sealant after the stair framing comes out, protection on the glass through the plaster and paint, and the film off at the end. The same rule applies as on every job: the film comes off when the trades are done, not later.

Next on the showers: field verification of sheets P-1 to P-4 as logged below.

17 November 2026 — Shop drawings P-1 to P-4 issued for sign-off

Where the job is: the field dimensions came in on a site sketch: four panels, a width and a height for each, and the notch marked in the bottom corner. From the sketch we issued a four-sheet drawing set, one panel per sheet, each with an elevation viewed from outside the shower, an enlarged detail of the notch, a specification block, a field verification table for the supervisor to fill in against the opening, and a production release block with three boxes: approved, approved as noted, or hold and re-measure.

What the sheets say:

MarkFloorSize W × H (in)Area (sq ft)Weight, 1/2-inch tempered (lb)
P-1265 3/4 × 83 9/1638.2about 248
P-2335 1/16 × 83 7/820.4about 133
P-3333 3/4 × 83 3/419.6about 128
P-4430 7/16 × 83 3/417.7about 115

Weights are from our calculator tool at 6.5 pounds per square foot for 1/2-inch glass. P-1 at about 248 pounds is a three-person lift up a townhouse stair with suction cups, and the drawing exists partly so that nobody tempers a 248-pound panel to a number read wrong off a sketch.

What we flagged before release:

Next: field supervisor verifies each sheet on site, fills in the measured column, circles glass type, writes in the hardware finish and signs; production release follows for any sheet marked approved. Anything marked hold goes back for a re-measure and a Rev 1 sheet.

November 2026 — Field dimensions taken

Site sketch with the four openings, floor by floor, width and height per panel and the notch marked in the corner. That sketch is the input to the drawing set above and is where the two unclear readings came from.

Why a Drawing for a Plain Rectangle

A fixed shower panel looks like the simplest piece of glass on a job: four edges and a couple of clamps. It is also the piece most often made twice, because a tempered panel cannot be trimmed, notched or drilled after the fact. One number read as 9/16 instead of 7/16, one notch in the mirror-image corner, one deduction taken twice, and the panel is scrap and the bathroom waits another two weeks. A one-page sheet per panel costs twenty minutes to draw and ten to verify, and it puts the person who measured, the person who checks and the person who releases on the same piece of paper with their names on it. That is the whole method, and it is the same for a frameless door with hinge cutouts as for these four rectangles with a notch.

Shop Drawings Issued for Sign-Off

The four sheets as issued on 17 November, Rev 0, before field verification. Measured values, circled options, signatures and the release box are filled in by hand on site.

Shop drawing P-1: fixed shower panel with 3/4-inch notch, floor 2, 65-3/4 by 83-9/16 inches, with field verification table and production release block
P-1, floor 2: 65 3/4 × 83 9/16. Both figures flagged VERIFY; the sketch is hard to read.
Shop drawing P-2: fixed shower panel with 3/4-inch notch, floor 3, 35-1/16 by 83-7/8 inches
P-2, floor 3: 35 1/16 × 83 7/8.
Shop drawing P-3: fixed shower panel with 3/4-inch notch, floor 3, 33-3/4 by 83-3/4 inches
P-3, floor 3: 33 3/4 × 83 3/4.
Shop drawing P-4: fixed shower panel with 3/4-inch notch, floor 4, 30-7/16 by 83-3/4 inches
P-4, floor 4: 30 7/16 × 83 3/4. The 7/16 could be 9/16 on the sketch; flagged VERIFY.

Related Pages

How we measure, verify and release shower glass for production · Fixed shower panels · Frameless shower doors · Low-iron vs Starphire glass for showers · Calculator tool: glass weight · Glossary: setting a fixed panel · Steel windows · 205 East 69th Street: steel windows, one block away · Reeded glass shower panel, Hudson Square · Manhattan windows, doors and glass · All Office News

Planning Something Similar?

If you have shower openings to glaze, in one bathroom or on every floor, send the sketch or ask us to measure. You get a drawing per panel to sign before anything is tempered, and the glass arrives fitting the opening it was drawn for.

Request a Quote   or call 929-235-1233