📞 929-235-1233 💬 WhatsApp 📧 Email

Can the Glass in a Pella or Marvin Wood Window Be Replaced, and How Do We Replace the Glazing Molding?

A fogged or cracked unit does not mean a new window. Here is how the glass comes out of a wood sash, how the wood glazing stops are removed, reused or milled new to the same profile, and what we did last week in the divided-lite windows of a SoHo townhouse.

← Back to News & Blog

In short: Yes. The insulated glass in a Pella, Marvin, Andersen or other wood window can be replaced without replacing the window, and in most of these windows the glass is held by a wood glazing stop (a small molding) on the inside of the sash rather than by putty or a snap-in vinyl bead. The job is to cut the sealant, remove the stops without splitting them, lift the old unit, set the new unit on fresh glazing tape and setting blocks, and refit the stops, or, where the old stops break or were never meant to come out, fit new wood stops milled to the same profile and paint them to match. We just finished exactly this on a townhouse in SoHo: new insulated units and new wood glazing moldings in divided-lite wood windows, done from inside with the sash in place.

When replacing the glass makes sense

Divided-lite wood window in a SoHo townhouse with new insulated glass and new unpainted wood glazing stops, looking out to a rear courtyard
SoHo: new glass set in the original wood sash, new stops in place before paint. The window, its frame, its hardware and its paint line on the outside are untouched.

A wood window from a major maker is built to last fifty years or more; its insulated glass unit is not. The seal around the edge of the unit fails somewhere between fifteen and thirty years depending on exposure, and the sign is fog or a tide line between the panes that no cleaning removes. The frame and sash are usually still sound. Replacing the whole window to cure a failed unit means a permit in most of New York City, a Landmarks review on a townhouse in SoHo, Greenwich Village or the Upper East Side, interior and exterior trim disturbed, and a lead time of weeks. Replacing the glass means a morning per window and nothing changes that anyone can see from the street.

The same job covers a cracked lite, a child's ball through a pane, an upgrade from clear to low-E or laminated glass for sound, and divided-lite windows where only one small pane is damaged. Where the sash itself is rotten, warped or will not hold a new unit square, we say so and price a sash or window replacement instead; see wood and clad windows.

How a wood window holds its glass

Three ways, and the first thing we check is which one you have:

On a divided-lite window the question is whether the bars are true divided lites (each pane its own small unit, each with its own stops) or a simulated divided lite (one big unit with bars applied to both faces and a spacer between the panes). True divided lites are replaced pane by pane; a simulated divided lite is one unit, and the new one comes from the glass shop with the internal spacer bars at the same spacing so the applied bars line up. The SoHo windows were true divided lites, so each pane was its own small job.

How we replace the glass, step by step

  1. Protect. Plastic on the outside of the opening (the blue tape and sheeting in the photographs), drop cloths inside, the sash left in place unless it comes out easily.
  2. Score the stops. The paint line between the stop and the sash is cut with a knife so the stop comes away cleanly and the paint on the sash does not tear.
  3. Lift the stops. A thin pry bar from the glass side, working along the length, with the pins pulled through the back of the stop rather than driven out. Stops that are sound are numbered and kept; stops that split, or that the maker glued in, are replaced.
  4. Cut the old unit free. The glazing tape or sealant bond is cut with a wire or a blade, the unit is lifted out, and the rabbet is scraped back to clean wood. Any soft wood at the bottom rail is the moment to stop and talk, because a new unit on a rotten rail will fail at the sill.
  5. Measure for the new unit. Rabbet to rabbet, less clearance, with the thickness of the old unit checked with a gauge; wood windows take 1/2" to 1" units depending on age and line. For a divided-lite sash every pane is measured; they are rarely identical.
  6. Set the new unit. Setting blocks at the bottom, glazing tape on the exterior rabbet, the unit pressed in and centered, and the gap at the edges left for the interior tape or sealant.
  7. Refit or replace the stops. The old stops go back in their numbered places, or new stops milled to the same profile are cut to length with the same mitered corners, pinned, and the pin heads filled. The joint between stop and glass is sealed. New stops are left unpainted for the painter, as in the photographs, or primed and painted by us where the owner asks.
Wood sash with divided lites showing new unpainted wood glazing stops around each new pane, SoHo Manhattan
Each pane with its own new stops, mitered at the corners, pinned and left for the painter.

Replacing the molding: matching the profile

New wood glazing stop molding fitted to a wood window sash before painting
A new stop fitted and ready for paint. Profile, width and corner cut match the originals so the finished window reads as untouched.

The stop is a small piece of wood but it is the only part of the repair that shows, so it has to be right. Pella and Marvin each use their own profiles, and they have changed them over the years; a stop from a current window will not match a 1990s sash. We take one original to the millwork shop and have the new stops run to that profile in the same species, usually pine or fir for painted windows and the matching hardwood for stained ones. Where the maker still supplies the part, we order it; where they do not, or the lead time is weeks, the millwork shop is faster and the result is identical once painted.

Corners are mitered to match the originals, lengths are cut to each pane, and the stops are pinned with headless brads rather than nailed so the wood does not split and the heads disappear under filler. On a stained window the stops are stained before fitting; on a painted one the painter follows us.

The SoHo project

Detail of a wood window sill and the lower glazing stop with new insulated glass set, interior view
At the sill: the new unit on its setting blocks, the bottom stop fitted, the joint ready to seal.

A townhouse in SoHo with divided-lite wood windows onto a rear courtyard, in a landmark district where the windows could not be changed from the outside and the owner did not want to change them anyway. Several units had failed seals and one pane was cracked. We replaced the glass in every affected pane from inside with the sash in place, fitted new wood glazing stops throughout the affected sashes so the finish would be uniform, sealed, and left the stops ready for the painter. The exterior was protected with sheeting during the work and shows no sign that anything was done, which is the point in a landmark district. Finished photographs follow once the painter has been.

What we need to quote

A photo of the window from inside showing the stops, a photo of the problem (fog, crack), the maker and line if you know it (a label is often on the sash edge or the jamb), and a count of the panes affected. From that we can tell you whether the stops can be reused or need milling, the glass make-up to match or upgrade, and the price per window. We do this work on Pella, Marvin, Andersen, Kolbe and older wood windows across Manhattan, Brooklyn, Queens and the suburbs; schedule a service call and we bring the glazing tape, blocks and a sample stop profile to the first visit. For the brand pages, see Pella and Marvin; for the glass itself, insulated glass units.

Questions People Ask

Can the glass in a Pella or Marvin wood window be replaced without replacing the window?

Yes. The insulated unit is held by a wood glazing stop on the inside of the sash; the stop is removed, the old unit lifted out, a new unit set on glazing tape and setting blocks, and the stop refitted or replaced. The frame, sash, hardware and exterior finish stay as they are.

How do I know the glass needs replacing?

Fog, haze or a tide line between the two panes that no cleaning removes means the edge seal has failed. A crack or chip in either pane is the other reason.

What is a glazing stop or glazing molding?

The small wood molding on the room side of a wood sash that holds the glass in. On Pella, Marvin and Andersen wood windows it is pinned to the sash and can be removed to change the glass.

Can the old molding be reused?

Often. Stops are scored along the paint line, pried gently and numbered. Stops that split, or that the maker glued, are replaced with new stops milled to the same profile.

Where do the new moldings come from?

From the window maker where the profile is still supplied, otherwise from a millwork shop that runs the stop to a sample of the original in the same species.

Can divided-lite windows have one pane replaced?

Yes, if the lites are true divided lites with their own stops. A simulated divided lite is one large unit and is replaced as a whole, with the internal spacer bars matched.

Does replacing glass in a landmark district need approval?

Replacing glass and interior stops in an existing sash does not change the exterior, so it is normally done without a Landmarks filing; replacing the window does need one. Confirm with your architect or expediter.

Can I upgrade the glass at the same time?

Usually. Low-E, laminated for sound or security, or a thicker unit can be fitted if the rabbet depth allows; we check the depth on the first visit.

How long does it take?

A morning per window for a typical sash from inside; divided-lite sashes take longer because each pane is handled separately. Painting the new stops is a separate step.

Related Reading

Glass replacement service Which screw do we use: wood, sheet metal and machine screws Pella windows Marvin windows Wood and clad windows Insulated glass units Pella windows Manhattan Marvin windows Manhattan How we measure a window opening

About this page. Written by Alex GC Inc. d/b/a Alex Glass Construction and reviewed before publication by Aleksandr Chernovolenko, Managing Partner, with our design and estimating lead and a field foreman. Our foremen hold the NYC DOB Site Safety Training supervisor card and our crews the 40-hour worker card; we are certified to fabricate, install and service Alutech and Everest aluminum systems. Facts are drawn from our own projects, manufacturer test data and the applicable codes; where we are giving an opinion, we say so. Last reviewed November 2026. Credentials

Fogged or cracked glass in a wood window?

Send a photo of the window from inside, a photo of the problem, and the maker if you know it. We will tell you whether the stops can be reused and quote the glass per window.